F701+

High-Speed A/D conversion and powerful digital processing capability of 500 times/sec.
High resolution of 1/10000 in all input range.
* It can be changed to 100times/sec.

Measurement can be performed quickly and precisely due to high speed A/D conversion.
 

Capable of adjusting filter automatically according to an operating condition. Helpful for setting at the test operation.

 

Equivalent calibration can be made easily by just inputting rated capacity and output of loadcell to F701+ with key button.

 

Temporary measurement stop, and Operation restart mode are available. Measurement can be performed continuously from the middle .

 

Set value can be restored, in case set value is changed by mistake.

 

■ Digital low pass filter
As it is resistant to vibration, measurement can be performed quickly and precisely.
*Conventional analog filter is also selectable
 

■ Sink type / source type are available
Type of I/O signal are selectable form Sink and Source.
 

■ Displaying accumulated value with one-touch
Accumulated value can be shown with one-touch
 

■ Connecting with printer by using RS-232C communication
Time data can be output for efficient data management.

■ Various optional interface
D/A converter, BCD output, RS-232C, RS485(Selectable from Modbus-RTU and UNI format), PROFIBUS-DP are available.
 

■ I/O board can be easily replaced on site
 

 

Analog｜Filter｜Display｜Setting｜External signal｜Interface｜General specification｜Attachment

Analog
Excitation voltage	DC10V±5% Output current： within 120mA  Remote sense type （Up to 4 350Ω load cells can be connected in parallel）
Signal input range	－0.5～3.0mV/V
Zero adjustment range	Automatic adjustment by digital processing　－0.5～2.0mV/V
Gain adjustment range	Automatic adjustment by digital processing　0.3～3.0mV/V
Min. input sensitivity	0.3μV/count
Accuracy	Non-linearity within  0.01%/FS   Zero drift within  0.2μV/℃ RTI   Gain drift within  15ppm/℃
A/D converter	Speed： Selectable from 500 times/sec, 100 times/sec Resolution： 24bit（binary）
Min. indicated resolution	1/10000
Secondary calibration	Equivalent calibration　 Min. indicated resolution during secondary calibration: 1/1000 (room temperature)

Filter
Analog	Low-pass filter　Selectable from 2, 4, 6, 8Hz （－12dB/oct）
Digital	Low-pass filter　Selectable from OFF, 1, 1.5, 2, 2.5, 3, 4, 5Hz

Display
Display unit	Character height 18.5mm　Numerical display (7 digits) by fluorescent display tube
Display value	5 digits, Sign; Minus sign displayed on most significant digit
Display frequency	Selectable from 3, 6, 13, 25 times/sec
Capacity	5 digits
Min. scale division	Can be set from 1 to 100
Over scale display	LOAD： A/D converter input over, －LOAD： A/D converter input minus over,  OFL1： Net weight over, OFL2： Capacity +9 scale division, OFL3： Gross weight over
Center zero	A true zero point or the center of each value is displayed.
Unit	Selectable from kg/g/t/lb/N/None
Status display	SP3/SP2/SP1/LOCK/ZT/ZALM/STAB/TARE/NET/GROSS/ HI LIM/HI/GO/LO/LO LIM/HOLD/NZ/CZ

Setting
Setting method	Settings are made by operating the membrane keys. Setting by RS-232C interface (option) and RS-485 interface (option) is also possible
Memory of set value	Calibration value and a part of set value: NOV.RAM (nonvolatile RAM) Other set values: F-RAM (nonvolatile RAM)
Protect of set value	Protect can be set by Lock switch and Lock parameter.
Setting item	Upper limit, Lower limit, Near zero, Set point 1, Set point 2, Compensation, Over, Under, Final, Comparison inhibit time, Judging time, Complete output time, Compensation feeding time, Number of times for AZ, Number of times for judging, Auto free fall compensation regulation value, Tare setting, Weighing function 1, Weighing function 2, Weighing function 3, Sequence mode, Function key inhibited, Filter, Motion detect, Zero tracking, Setting value LOCK, Balance weight value, Capacity, Min. scale division, Net over, Gross over, DZ regulation value, Function selection, Compensation for gravitational acceleration, Zero calibration, Span calibration, Equivalent calibration, Input selection, Output selection, Moving average filter, Restart setting set point 1, Restart setting set point 2, Restart setting set point 3

External signal You can specify whether PNP (Source) type or NPN (Sink) type when order the F701+.
Output signals （12 points）	NZ, SP1, SP2, SP3, Under, Over, Lower limit, Upper limit,  Stable, Output selection 1, Output selection 2, Output selection 3  Output turns ON when transistor is ON. * PNP（source）type: External voltage must be prepared separately by customer.
Input signals （8 points）	G/N, D/Z, One-touch tare subtraction, Input selection 1,  Input selection 2, Input selection 3, Input selection 4, Input selection 5 Contact (relay, switch etc.) or non-contact (transistor, open collector etc.) can be connected. * PNP（source）type: External voltage must be prepared separately by customer.

Interface 2 optional interface can be added in addition the standard interface. ＊1(mark): only 1 option is available. ＊2(mark): only 1 option is available.
SIF	2-wire type serial interface
232	RS-232C communication interface（Option）＊1
485	RS-485 communication interface（Selectable from Modbus-RTU, UNI format）（Option）＊1
BCO	BCD parallel data output interface (Option)＊2
DAC	D/A converter (Option)＊2
PRF	PROFIBUS interface (Option) ＊PROFIBUS-DPV0  ＊2

General specification
Power supply voltage	AC100～240V（＋10％－15％）（free power source 50/60Hz）
Inrush current	1.5A, 1ms AC100V average load condition （cold start at room temperature） 2.5A, 1ms AC200V average load condition （cold start at room temperature）
Power consumption	7W typ
Operating conditions	Operation temperature：－10～＋40℃　Storage temperature：－20～＋85℃　 Humidity： 85％RH or less（non-condensing）
Dimensions	192（W）×96（H）×160（D）mm（Projections excluded）
Weight	Approx. 1.5kg

Attachment
AC input cord（Nominal rating 125V）2m	1
Load cell connector	1
Mini-screwdriver	1
57 series 24p connector for external input / output	1
Operation manual	1
BCD output connector ×1（with BCD output option）	1
D/A converter connector ×1（with D/A converter option）	1

Model	Interface
232	RS-232C communication interface
485	RS-485 communication interface（Selectable from Modbus-RTU, UNI format）
BCO	BCD parallel data output interface
DAC	D/A converter
PRF	PROFIBUS interface ＊PROFIBUS-DPV0

Model	Description
CAAC2P-P2	AC input cord 2m
CAAC3P-CEE7/7-P1.5	AC input cord（Voltage resistance:250V）1.5m
CA4131	（6-wired）cable with JRC connector at one end 3m
CA4230	JRC-PRC （6-wired）conversion relay cable 0.3m
CA4311	JRC-PRC （6-wired）conversion relay cable （4-wired to 6-wired） （for 520A use）1m
CN3P-2P	3P-2P converter plug for AC input cord
CN10	Loadcell connector（JRC connector）
CN21	57 series 36p connector for BCD output
CN23	57 series 24p connector for external input / output
CN34	D-Sub 9p connector for RS-232C