Details

---

 

Product outline

F377A is a digital indicator integrated with a voltage / current output type sensor that can display physical quantities such as pressure, load and torque in waveforms. It can be connected to the voltage of ±10V and the current of ±20mA. It is able to visually capture in waveforms the fluctuations in physical quantities which are difficult to capture by only numerical values.
With a maximum 2000 times per second for high-speed processing, it is also ideal for narrow value fluctuations and comes equipped with a HI/LO limit comparison function, various hold functions and judgment function.
F377A is the best digital indicator for graders and testers used in results judgment of assembling work and auto machining.

Specifications

Analog section｜Display section｜Setting section｜Hold section｜Comparison function｜External signal｜Interface｜General performance｜Attachments

Analog section
Voltage input	-10 to +10V, Input impedance 1MΩ or more
Current input	-20 to +20mA, Input resistance Approx.250Ω
Accuracy	Non-linearity: within 0.02%/FS ±1digit (at a 10V or 20mA input) Zero drift: within 0.2mV/℃ RTI or within 0.4μA/℃ RTI Gain drift: within 0.01%/℃
Analog filter	Low pass filter (-6dB/oct.) Selectable at 30, 100, 300, 1000Hz
A/D converter	Speed: 2000 times/sec. Resolution: 24bit (binary) Effective resolution: Approx. 1/30000 to 10V or 20mA input
Analog monitor output	Output level: Approx. 0.6V per 1V input or approx. 0.3V per 1mA input Load resistance: 2kΩ or higher

Display section
Display unit	TFT color LCD module 3.5inch
Display area	71(W) mm×53(H) mm
Dot structure	320×240dot
Measured value	5 digits: -99999 to +99999, Sign: Minus sign on most significant digit

Setting section
Comparison functions	HH, Hi, Lo, LL, Hysteresis, alarm Hi, alarm Lo, near zero, comparison timing, comparison output selection
Hold setting	Hold mode, detection start level, detection time, level detection condition, sample point shift value, detection end level, average sample number, inflection point judging value, pre-inflection point slope detection time, post-inflection point slope detection time, inflection point shift, detection start condition, peak-valley detection min. value, peak-valley detection amplification
Graph setting	Graph mode, Y-axis (load) start point, Y-axis (load) end point, X-axis (time) end point, plotting start level, interval time, plotting start level conditions
Calibration setting	Analog input selection, zero calibration, equivalent input calibration, actual load calibration, calibration value selection, unit, minimum scale, digital offset, digital zero limit
Operation setting	Digital filter, analog filter, backlight lighting time, language change, SI/F print, motion detect, zero tracking, monitor output filter, display color of measured value, B5 function selection, B6 OFF detection standby time, B8 OFF detection standby time, measured work input change, control input change, password
RS-232C setting	Communication mode, baud rate, character length, stop bit, parity bit, delimiter, flow control
Extended comparison function	Previous value comparison, relative value comparison
Extended hold function	Double hold, auto reset change, hold value update, sample trigger change, hold cancel at DZ, hold END timing
Extended graph function	Pre-trigger display
Extended operation function	Digital filter characteristics, average time at DZ, RUN output format
Extended option	BCD output data format

Hold section

Hold

1) Sample, 2) Peak, 3) Valley, 4) P-P, 5) Average, 6) Inflection Point, 7) Relative Maximum, 8) Relative Minimum, 9) Relative Difference, 10) Sample & Peak, 11) Sample & Valley, 12) Sample & P-P, 13) Sample & Average, 14) Sample & Inflection Point, 15) Sample & Relative Maximum, 16) Sample & Relative Minimum, 17) Sample & Relative Difference, 18) Peak & Valley, 19) Peak & P-P, 20) Valley & P-P, 21) Average & Peak, 22) Average & Valley, 23) Average & P-P, 24) Relative Maximum & Relative Minimum, 25) Relative Maximum & Relative Difference, 26) Relative Minimum & Relative Difference

Comparison function
	Higher Hi (HH) limit setting, Lower Lo (LL) limit setting, High (HI) limit setting, Low (LO) limit setting

Calibration value selection
	Stores up to 4 types of calibration value that can be interchanged

External signal
External output signal (8 points)	HI/LO comparison output (HH, HI, OK, LO, LL)/ RUN output/ hold end output/ graph plotting end output Vce=30V (max), Ic=30mA (max)
External input signal (10 points)	Work selection input/ hold control input/ digital zero input (DZ)/ graph plotting control input/ calibration selection input lc=10mA or lower

Interface
SIF	2-wire type serial interface
232	RS-232C communication interface
BCO	BCD parallel data output interface (Option)
DAV	D/A converter voltage output (Option)
DAI	D/A converter current output (Option)
ODN	DeviceNet interface (Option)
CCL	CC-Link interface (Option)

General performance
Power supply voltage	DC24V (±15%)
Power consumption	18W max
Operating conditions	Temperature: operation temperature　-10℃ to +40℃ Storage temperature　-20℃ to +60℃ Humidity: 85%RH or lower (non-condensing)
Inrush current (typ)	55A, 1msec (cold start at room temperature)
Dimensions	96(W)×96(H)×138(D) mm (protruding areas are not included)
Weight	Approx. 1.0kg

Attachments
FCN series I/O connector (with cover)	1
Jumper cable	1
Operation manual	1
BCD output connector (when BCD output option is installed)	1
Mini driver (when D/A converter　option is installed)	1
DeviceNet connector (when DeviceNet option is installed)	1
CC-Link connector (when CC-Link option is installed)	1

Option

Model
BCO	BCD parallel data output interface
DAV	D/A converter voltage output
DAI	D/A converter current output
CCL	CC-Link interface
ODN	DeviceNet interface

Optional accessories

Model
CA372-I/O	3m end treatment 24-leads cable with FCN connector at one end
CA81-232X	1.5m miniDIN-D-Sub9p cross cable
CN50	FCN series I/O connector (with cover)
CN55	FCN series I/O connector (with diagonal cover)
CN60	Circular DIN 8p connector for RS-232C
CN51	BCD output connector
CN71	CC-Link connector
CN80	Analog I/O connector terminal
CND01	DeviceNet connector
GMP96×96	Rubber packing

Download

Product catalogue(PDF)		GC2015_F377A(417 KB)